tail servo 9254 kok gampang hangat2 kuku ya?...hehehehe

Diskusi tentang heli elektrik

Moderators: Budiman, irsansaputra

Post Reply
User avatar
Budiman
First Lieutenant
First Lieutenant
Posts: 1271
Joined: 17 Jan 2007, 15:27
Location: bekasi-surabaya
Contact:
Contact Budiman

tail servo 9254 kok gampang hangat2 kuku ya?...hehehehe

Post by Budiman »

Alo temen2,

Saya ada pertanyaan neh...tail servo 9254 pd heli saya ko terasa hangat ya..padahal tidak ada binding pd linkage rod dan tail slidder juga lancar2 aja..tidak ada hambatan... :-k ...
Apakah perlu dipasang semacam regulator step down ya?..
Terima Kasih sebelumnya

salam,

Budi
Top
User avatar
andre77
Technical Sergeant
Technical Sergeant
Posts: 388
Joined: 17 Jan 2007, 14:38
Location: BANJARMASIN
Contact:
Contact andre77

Post by andre77 »

Servo digital emang kaya gitu pak makanya menyedot lebih banyak arus di banding servo analog
Top
User avatar
rpramusinto
Senior Airman
Senior Airman
Posts: 127
Joined: 26 Jan 2007, 00:48
Location: Bekasi
Contact:
Contact rpramusinto

Post by rpramusinto »

setuju sama om andre... yg jelas kalo gyro + digital servo refresh rate nya lebih tinggi, jadi si servo selalu dalam posisi mengkoreksi arah tail, atau selalu siaga kalau2 si buntut gak nurut.. hehehe wajar kok mas budi... hampir semua servo digital yg hi-speed tingkah nya sama...
Top
User avatar
Syafik
Major General
Major General
Posts: 4026
Joined: 22 Jan 2007, 13:24
Location: Gresik - Surabaya
Contact:
Contact Syafik

Post by Syafik »

servo cerdas sehingga otaknya gak pernah lengah, akhirnya butuh makan banyak suhu badannya agak tinggi... hehehe
Top
User avatar
rpramusinto
Senior Airman
Senior Airman
Posts: 127
Joined: 26 Jan 2007, 00:48
Location: Bekasi
Contact:
Contact rpramusinto

Post by rpramusinto »

Syafik wrote:servo cerdas sehingga otaknya gak pernah lengah, akhirnya butuh makan banyak suhu badannya agak tinggi... hehehe


Setuju pm syafik... penjelasan yg sangat logis.. hihihihi :D
Top
User avatar
Roy_95
Senior Airman
Senior Airman
Posts: 151
Joined: 24 Sep 2007, 15:18
Location: Manado
Contact:
Contact Roy_95

Post by Roy_95 »

asal jangan hangat-hangat t@1 ayam...? :D...hahaha
Top
User avatar
Budiman
First Lieutenant
First Lieutenant
Posts: 1271
Joined: 17 Jan 2007, 15:27
Location: bekasi-surabaya
Contact:
Contact Budiman

Post by Budiman »

Roy_95 wrote:asal jangan hangat-hangat t@1 ayam...? :D...hahaha


maksudnya apa ya... :-k
Top
User avatar
Budiman
First Lieutenant
First Lieutenant
Posts: 1271
Joined: 17 Jan 2007, 15:27
Location: bekasi-surabaya
Contact:
Contact Budiman

Post by Budiman »

Alo temen2,
Berikut ini data2 yg saya dapat dari website masing2 manufacturer..

Ini nilai BEC output dr 35A Brushless ESC(Governer Mode) RCE-BL35X by Align :
●BEC output voltage(6V) to show great performance on the torque & speed of servo


Sedangkan ini spec dr servo 9254 :

SPECS: Speed: .06 sec/60° @ 4.8V
Torque: 47.2 oz-in @ 4.8V
Length: 1.6" (41mm)
Width: .8" (20mm)
Height: 1.4" (36mm)
Weight: 1.7oz (49g)
Power Supply: 4.8V (Futaba does NOT recommend using 6V)

Mudah2an bisa memberikan kejelasan buat kita semua..termasuk saya

salam,

Budi
Top
User avatar
Syafik
Major General
Major General
Posts: 4026
Joined: 22 Jan 2007, 13:24
Location: Gresik - Surabaya
Contact:
Contact Syafik

Post by Syafik »

perlu pake step down ke 4,8volt om... memang spek servo 9254 tidak recommended untuk 6volt, bisa kobong ntar... ada gak pengalaman teman2 menggunakan servo ini di trex450 tanpa step down, share dong?
Top
User avatar
e12ry
Airman First Class
Airman First Class
Posts: 70
Joined: 06 May 2007, 20:05
Location: -Earth-

Post by e12ry »

step down align..... 5.1....
Top
Post Reply

Return to “RC Heli : Electric Motor Powered”