Page 1 of 2
RC TX PPM Output - Pin Assignment, tuk simulator
Posted: 23 Jun 2009, 21:26
by DeVIN
Pasti bermanfaat, .......
http://www.mftech.de/buchsen_en.htmdan
Aplikasinya, Oscilloscope 2.51
zip file
Re: RC TX PPM Output - Pin Assignment, tuk simulator
Posted: 23 Jun 2009, 22:09
by atari7up
Re: RC TX PPM Output - Pin Assignment, tuk simulator
Posted: 25 Jun 2009, 00:06
by dion
mantap om sharing nya
thanks
Re: RC TX PPM Output - Pin Assignment, tuk simulator
Posted: 25 Jun 2009, 00:23
by DeVIN
Lanjut om, ....
di situ dijelaskan pula bahwa kalo pake tx walkera atau seperti DF4 yang signal ppmnya gak murni, ternyata bisa diambil langsung dari colokan kristal-nya, dsb.
Berarti cukup uptodate tuh infonya.
Salam.
Re: RC TX PPM Output - Pin Assignment, tuk simulator
Posted: 25 Jun 2009, 14:30
by iwan21
DeVIN wrote:Lanjut om, ....
di situ dijelaskan pula bahwa kalo pake tx walkera atau seperti DF4 yang signal ppmnya gak murni, ternyata bisa diambil langsung dari colokan kristal-nya, dsb.
Berarti cukup uptodate tuh infonya.
Salam.
yg saya bold itu, persis sama dg kalo kita pake tx asli bawaan WD, dulu utk FMS saya pake remote ini sebabnya dan output PPM ambil dari soket xtal
Re: RC TX PPM Output - Pin Assignment, tuk simulator
Posted: 25 Jun 2009, 16:27
by BERTHIE FLYER
ngeri.... sepertinya Pembahasan tingkat tinggi ini.....
Re: RC TX PPM Output - Pin Assignment, tuk simulator
Posted: 25 Jun 2009, 16:42
by didin
Bermanfaat ...? Ya....
Tapi elmu belum nyampai....
Re: RC TX PPM Output - Pin Assignment, tuk simulator
Posted: 26 Jun 2009, 01:05
by DeVIN
@All,
Ya om,...paling tidak disticky nih threadnya tuk informasi dikemudian hari.
Salam.
Re: RC TX PPM Output - Pin Assignment, tuk simulator
Posted: 25 May 2010, 15:17
by coyo
Kaya'nya penomoran pin di gambarnya salah:
seharusnya begini:
btw, ini PC osciloscope yg lebih advance:
www.zeitnitz.de/Christian/Scope/Scope_en.htmlFree for personal use.....
Re: RC TX PPM Output - Pin Assignment, tuk simulator
Posted: 28 May 2010, 23:36
by DeVIN
Makasih ya om atas updatenya.
Tapi kayanya keterangannya sama dengan sistem penomorannya, jadi hanya beda sistem penomorannya tetapi arti sama.
dan info tersebut adalah penomoran standar, see
http://en.wikipedia.org/wiki/DIN_connector"Pins on male connectors are numbered (from right to left, viewed from outside of the connector, with the 5 pins upwards, and facing them): 1–4–2–5–3. Holes on female connectors are also numbered 1-4-2-5-3, but from left to right (facing the holes). "
GND: 0 = shielding
Signal: 4
short-circuit 3 with 5
( 1: Bat+, 2: Signal in, 5: Bat+, 6 : +5V )
Salam.
